![]() If however you area sealing a white or off-white Marble and you not wish to darken the stone apply a single coat of Tile Doctor Ultra-Seal which provides a natural look finish. When the tiles are fully dry apply either one coat of Tile Doctor Colour Grow to enhance the natural colours of darker Marble’s. 4 Green Burnishing pad until a nice light sheen has been achieved, this will tighten up the pores of the Marble thus making it easier to seal and maintain. ![]() Leave to dry overnight and then finish with a No. Make sure to thoroughly rinse the tiles after using Duo Clean to remove any trace of chemicals otherwise it may impact the sealer when it is applied. If the grout is in need of attention then clean the grout at this point using Tile Doctor Duo Clean which is a very effective grout cleaning product as well as treating mould. This method is also the best way to treat the build-up of Limescale as the acidic cleaners commonly available for this will actually damage the Marble. Then switch to a No.2 Blue Burnishing pad and repeat the process followed by a No. The process is thus, spray the No.1 Red Burnishing pad with water then apply to the wall tile until the dirt and old sealer had been removed. ![]() The best way to clean and polish Marble wall tiles is with a hand-held polishing machine using a set of six inch Burnishing pads, we find using chemicals less effective on vertical surfaces and can lead to staining. In normal circumstances allow 24 hours for the stone to dry out before sealing, a damp meter can be used to verify when the stone is dry. Rinse thoroughly with clean water to make sure the floor is neutralised of any chemicals. Add water as you go to lubricate the process and then use a wet Vax to extract the soiled solution from the floor. When fully polished protect the floor by applying a sealer as per instructions below.Īlternatively spray undiluted Tile Doctor Remove and Go onto the stone (use as directed), leave to dwell for ten to fifteen minutes (if necessary add more product to prevent it drying out) then agitate with a scrub brush or a black buffing pad fitted to a buffing machine. 4 Green burnishing pad and polish with a squirt of water. Leave to fully dry and then complete by applying a No. Again remove the water with a wet Vax machine and then scrub the grout joints with Pro-Clean diluted 1:5 parts water. Next take off the coarse pad and apply a No2 Blue burnishing pad and repeat the process followed by the No.3 Yellow burnishing pad. If you have the use of a 150 RPM (or slightly higher) buffing machine restore the honed finish by burnishing the floor using a No.1 Red burishing pad to take off the old sealer and ground in dirt, add water to the area and then go over each tile with the pad 3 or 4 times, then remove the dirty water using a wet vax and rinse the floor. The advice below will help you maintain Marble to a good standard however please note Marble is a sedimentary stone as such it’s generally very porous and acid sensitive and can be damaged through the use of even mildly acidic soaps, shampoos and body washes, therefore Tile Doctor do not recommended it for use in wet rooms, shower cubicles or near swimming pools. It is often the preferred choice for interior and exterior in both commercial and domestic for flooring, wall cladding, paving, facades of buildings, railway stations, pavement, landscaping, garden stone. ![]() Our products are used in a wide range of cleaning applications because of their potency.Often reputed in the international market for its premium quality, toughness and durability. Strict inspection of the quality of our products is carried out in order to ensure that clients get the best products from us. We make products of the best quality available to clients at extremely affordable prices in an assortment of specifications. These products are highly acclaimed for their gentle cleaning action, because of which the product gets cleaned without any damage. The manufacturing process is carried out at our ultramodern infrastructure facility by using modern production technology. The products offered by us are manufactured in strict compliance with industrial standards of quality by using premium quality ingredients and materials. Established in the year 2014 at Mumbai, we, MK Laboratories and Research Center, are a highly acclaimed Manufacturer of premium quality Commercial Cleaners and Polishes, Automobile Cleaners And Polishes, Household Cleaners And Polishes, Silicone Emulsion and many more.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |